Heat Reflective Paint (Premium)

Product introduction

Heat Reflective Paint (Premium)
19HR-P

Application

– Residential and commercial facilities such as houses, apartments, studio apartments, and plants
– Different kinds of commercial facilities such as plants and shopping complexes
– Outdoor facilities

Previous screen

Product configuration

Heat Reflective Paint (Premium) product is a premium heat barrier paint, which uses high-functional acrylic emulsion as sealant for providing high reflectivity of sunlight and effectively reducing the energy required for cooling buildings. It is easy to conduct work and dry fast using aqueous paint and is applicable to rooftops and other areas of the building with excellent adhesion, resistance to contamination, weather protection, and gloss retention rate.

Product characteristics

– It provides high thermal barrier performance with thin membrane (60~100㎛).
– It is not easily contaminated due to excellent resistance to acid and alkali.
– It is highly resistant to cracks and has strong adhesion.
– It is easy to carry out roller work.
– It can minimize the process with construction by two times.

Product characteristics

Product volume	18L	Tools	Airless, roller, brush
Color	White, light gray, light green **Mixing color is possible (contact manufacturer)	Recommended dry membrane	60~100㎛ /Only two coats
Gloss	Gloss	Construction area	Approx. 50~60㎡ (15 ~ 18 pyeong)
Painting type	Liquid type	Theoretical painting area	3.6~6㎡ /ℓ
Thinner	Water	Drying(20℃)	Touch dry	Hard dry	Recoat interval
Mixing ratio	Less than 10%	hours	1hours	2hours	5hours

How to use and caution

How to use	– Painting condition is where ambient temperature is at 5~35℃ and humidity is at 80% or below. – Mix the paint sufficiently before using on construction. – After going through surface processing, apply paint so that primer can penetrate deeply into the painting surface. – After applying primer on the surface, dry for 4 hours at 20℃ and apply top coating twice. Aqueous paint can be used for mixing color. (basic color: white) Minimum amount for mixing color is 50 packs or above. (pastel color is possible)
caution	– Concrete surface should be sufficiently cured (4 weeks or above at 20℃) and apply paint when pH is 8 ~ 9 or below and moisture content is 8% or below. – Aqueous paint should be stored in indoor areas (at room temperature of 5℃ or above) that can avoid direct light. – Crack area should be filled and surface should be flattened using filler after applying V cutting – If surface processing is insufficient, it might lead to poor adhesion and detachment of membrane. – In case of exceeding recommended amount (within 10%) of diluent (water), it might lead to reduction in material property. – In case of applying paint on the previous membrane, check for the suitability with previous membrane before using. – Color difference might occur on the product with same color and lot depending on the dilution ratio, painting device, and painting method, so check the color before painting.

How to use

– Painting condition is where ambient temperature is at 5~35℃ and humidity is at 80% or below.
– Mix the paint sufficiently before using on construction.
– After going through surface processing, apply paint so that primer can penetrate deeply into the painting surface.
– After applying primer on the surface, dry for 4 hours at 20℃ and apply top coating twice.
** Aqueous paint can be used for mixing color. (basic color: white)
**Minimum amount for mixing color is 50 packs or above. (pastel color is possible)

caution

– Concrete surface should be sufficiently cured (4 weeks or above at 20℃) and apply paint when pH is 8 ~ 9 or below and moisture content is 8% or below.
– Aqueous paint should be stored in indoor areas (at room temperature of 5℃ or above) that can avoid direct light.
– Crack area should be filled and surface should be flattened using filler after applying V cutting
– If surface processing is insufficient, it might lead to poor adhesion and detachment of membrane.
– In case of exceeding recommended amount (within 10%) of diluent (water), it might lead to reduction in material property.
– In case of applying paint on the previous membrane, check for the suitability with previous membrane before using.
– Color difference might occur on the product with same color and lot depending on the dilution ratio, painting device, and painting method, so check the color before painting.

Product introduction