Heat Reflective Paint (General)

Product introduction

Heat Reflective Paint (General)
19HR-G

Application

– Residential and commercial facilities such as houses, apartments, studio apartments, and plants
– Storage facilities such as storage tanks, logistics warehouses, silos, and panels
– Outdoor facilities such as barns, pig farms, chicken coops, containers, and bridges

Previous screen

Product configuration

Heat Reflective Paint (General) product uses acrylic emulsion as sealant for thermal barrier paint to provide high reflectivity of sunlight and to reduce the energy required for cooling buildings. It is easy to conduct work and dry quickly using aqueous paint and is applicable to rooftops and other areas of buildings with excellent adhesion and weather protection.

Product characteristics

– It can minimize the process with construction by two times.
– It provides high thermal barrier performance with a thin membrane (80~100㎛).
– Tacking does not occur (becoming sticky) after construction, so contamination does not occur.
– It has excellent weather protection, crack resistance, and adhesion.
– Viscosity does not change much depending on temperature change.
– It has excellent workability.

Product characteristics

Product volume	18kg	Tools	Airless, roller, brush
Color	White **Mixing color is possible (contact manufacturer)	Recommended dry membrane	80~100㎛ /Only two coats
Gloss	Matte	Construction area	Approx. 50㎡ (15 ~ 18 pyeong)
Painting type	Liquid type	Theoretical painting area	3~6㎡ /ℓ
Thinner	Water	Drying(20℃)	Touch dry	Hard dry	Recoat interval
Mixing ratio	Less than 10%	hours	1 hours	2 hours	3 hours

How to use and precautions

How to use	– Painting condition is where ambient temperature is at 5~35℃ and humidity is at 80% or below. – Mix the paint sufficiently before using on construction. – After going through surface processing, apply paint so that primer can penetrate deeply into the painting surface. – After applying primer on the surface, dry for 4 hours at 20℃ and apply top coating twice. Aqueous paint can be used for mixing color. (basic color: white) Minimum amount for mixing color is 50 packs or above. (pastel color is possible)
precautions	– Concrete surface should be sufficiently cured (4 weeks or above at 20℃) and apply paint when pH is 8 ~ 9 or below and moisture content is 8% or below. – Aqueous paint should be stored in indoor areas (at room temperature of 5℃ or above) that can avoid direct light. – Crack area should be filled and surface should be flattened using filler after applying V cutting. – If surface processing is insufficient, it might lead to poor adhesion and detachment of membrane. – In case of exceeding recommended amount (within 10%) of diluent (water), it might lead to reduction in material property. – In case of applying paint on the previous membrane, check for the suitability with previous membrane before using. – Color difference might occur on the product with same color and lot depending on the dilution ratio, painting device, and painting method, so check the color before painting.

How to use

– Painting condition is where ambient temperature is at 5~35℃ and humidity is at 80% or below.
– Mix the paint sufficiently before using on construction.
– After going through surface processing, apply paint so that primer can penetrate deeply into the painting surface.
– After applying primer on the surface, dry for 4 hours at 20℃ and apply top coating twice.
** Aqueous paint can be used for mixing color. (basic color: white)
** Minimum amount for mixing color is 50 packs or above. (pastel color is possible)

precautions

– Concrete surface should be sufficiently cured (4 weeks or above at 20℃) and apply paint when pH is 8 ~ 9 or below and moisture content is 8% or below.
– Aqueous paint should be stored in indoor areas (at room temperature of 5℃ or above) that can avoid direct light.
– Crack area should be filled and surface should be flattened using filler after applying V cutting.
– If surface processing is insufficient, it might lead to poor adhesion and detachment of membrane.
– In case of exceeding recommended amount (within 10%) of diluent (water), it might lead to reduction in material property.
– In case of applying paint on the previous membrane, check for the suitability with previous membrane before using.
– Color difference might occur on the product with same color and lot depending on the dilution ratio, painting device, and painting method, so check the color before painting.

Product introduction